Boiler
Boiler Repair in Brooklyn & Across NYC
Boiler repair in Brooklyn and across New York City, from pre-war steam systems in brownstones to modern hot-water and combi boilers in newer construction. Our network of residential boiler specialists diagnoses the real problem on the first visit — not just the symptom.
Based in Brooklyn and serving every borough plus Long Island, we see more boiler failures during a single January cold snap than most companies see all year. New York's older housing stock — Brooklyn's brownstones and rowhouses especially — means a huge share of the city still runs on steam boilers with radiators, while newer construction and renovated homes increasingly rely on hot-water or combi systems. Both fail differently, and both are common calls for our team every week of the heating season. A steam system that won't come up to pressure has almost nothing in common, mechanically, with a hot-water system that won't circulate — which is why diagnosis has to start with figuring out which type of system is actually in the building, not just which symptom is showing up at the radiator.
Whether it's a boiler that won't fire, a pilot that won't stay lit, banging pipes, uneven heat between floors, or a pressure gauge stuck in the red, we send a technician equipped to test ignition components, pressure relief valves, circulator pumps, low-water cutoffs, and aquastat or steam controls on-site so most repairs are completed in a single visit. Boiler repair also covers the heating side of a combi unit — a boiler that supplies both radiators and domestic hot water — where a heat-side fault can sometimes masquerade as a hot-water complaint or vice versa.
This page covers boiler heating-system repair specifically — sometimes searched as "heating repair" or "no heat" service, since for a building running on a boiler and radiators, those are the same call. If your building instead has forced-air furnaces and ductwork, that's a different type of system than what's covered here.
Warning Signs
Signs You Need Boiler Repair
No heat or intermittent heat across radiators
Loud banging, clanking, or whistling from pipes or the boiler itself
Pilot light won't stay lit or keeps going out
Water pooling around the base of the unit
Pressure gauge reading unusually high or low
Yellow or flickering burner flame instead of steady blue
One or more radiators staying cold while others heat normally
A boiler control panel showing a lockout or fault code
Common Causes
What Usually Causes This
Realistic explanations, not a diagnosis of your specific property — an on-site visit confirms the actual cause.
- Trapped air in radiators or piping, which shows up as banging, whistling, or rooms that never fully heat
- A failed or sticking pilot/ignition component, common on older standing-pilot steam boilers
- Low water in a steam system, which trips the low-water cutoff and shuts the burner down as a safety measure
- Mineral buildup or sediment in an aging hot-water system, reducing circulation and heat transfer
- A circulator pump that's seized, wired incorrectly, or simply worn out on hot-water and hydronic systems
- Radiator or main vents that are clogged, painted over, or the wrong size for the run — a frequent issue in older steam buildings
- A pressure relief valve or expansion tank that's failed, which shows up as a gauge stuck high or water pooling near the unit
Our Process
How It Works
Initial assessment
We ask what's happening — no heat, partial heat, noise, a code on the panel — and confirm whether the system is steam, hot-water, or combi before touching anything.
Safety checks
Before any diagnostic work, we check for signs of a gas or combustion problem, verify the low-water cutoff is functioning, and confirm venting is clear.
System testing
We run the boiler through an ignition and heat cycle while watching pressure, water level, burner flame, and controls to see the fault happen in real time.
Diagnosis
Once the failure point is isolated, we explain in plain terms what's actually wrong and why — not just which part will be replaced.
Repair options
You get a clear, itemized estimate covering the repair, with any reasonable alternatives explained, before we proceed.
Testing after repair
We run a full heat cycle post-repair to confirm the fix holds under real operating conditions, not just at idle.
Cleanup & recommendations
We leave the mechanical room as we found it and flag anything else worth watching, like an aging expansion tank or a part that's near end-of-life.
Emergency Service
Emergency Boiler Repair, Nights and Weekends
A boiler failure in the middle of winter isn't a next-week problem — it's a tonight problem. We treat total loss of heat as an emergency and dispatch technicians across Brooklyn and the rest of New York City nights, weekends, and holidays, not just during standard business hours. If you're dealing with no heat during freezing temperatures, water leaking near the unit, or a carbon monoxide detector that's alarmed, call us right away rather than waiting for morning.
Repair vs. Replacement
Which One Actually Makes Sense
Repair Often Makes Sense When
- The failure is isolated to a single component — an ignition module, circulator pump, valve, or control — on a system that's otherwise sound
- The boiler is roughly mid-life for its type and has no history of recurring failures
- Repair parts are still available for the model
Replacement Often Makes Sense When
- Repairs on the same unit have become frequent within a short span
- There's visible rust, cracking, or corrosion on the boiler shell or heat exchanger itself, not just surface piping
- The unit was already oversized or undersized for the building, so repairs fix the symptom but not the underlying comfort or efficiency problem
- Replacement parts for the specific model are discontinued or difficult to source
Age alone isn't a reliable reason to replace a boiler that's otherwise running well — a well-maintained unit can outlast a poorly-maintained newer one. We'll give you a straight comparison of repair cost against replacement during the visit rather than pushing one option by default.
Pricing Guidance
Typical Cost Factors
Boiler repair costs vary by what's actually failed and how the specific system is set up, so we don't publish flat prices — but the main factors that move a repair estimate are consistent across jobs:
Final pricing depends on an on-site assessment, system condition, access, parts, and the approved scope of work.
NYC Considerations
What's Different About NYC Housing
- A large share of NYC's housing stock, especially in Brooklyn, Manhattan, and the Bronx, still runs on prewar steam systems with radiators — these have different failure points than the hot-water systems common in newer construction and Long Island homes
- Multifamily and co-op buildings often share a single boiler across many units, which can mean coordinating access and timing with building management or a super
- Basement mechanical rooms in rowhouses and brownstones are frequently tight and shared with storage, laundry, or a second unit, which affects how a repair is staged
- Older buildings sometimes still have galvanized or original piping runs feeding the radiators, which can complicate a repair that would be simple on newer piping
- Where a repair involves gas line work or crosses into permit-required territory, that portion is coordinated through our licensed partner network (see our Licensing & Compliance page)
Our Work
Before & After
Photo gallery of specific completed jobs coming soon — here's what the visit typically looks like.
Boiler Repair photos coming soon
Boiler Repair photos coming soon
Reviews
What Homeowners Say
“I had a leak in my living room ceiling and couldn't figure out where it was coming from. Keon and his employee showed up quickly after I reached out. They were professional, patient, and took the time to explain everything to me.”
Lisa B.
Brooklyn, NY · Pipe Repair
“Worked on the complicated pipes in our 125-year-old home. We were satisfied with the work and would hire again.”
Makeba D.
Brooklyn, NY · Pipe Repair
“Keon was able to come the same day. He was very meticulous pinpointing the issue and tried to be as minimally invasive as possible.”
Elias Z.
Brooklyn, NY · Pipe Repair
Service Area
Boiler Repair Across New York
Choose your borough for local details and neighborhood coverage.
FAQ
Frequently Asked Questions
Boiler repair costs depend on which component failed, whether the system is steam, hot-water, or combi, and how accessible the mechanical room is — so we don't publish flat rates, since they'd be misleading before a technician sees the system. You'll get an itemized estimate before any repair work begins, so there are no surprises on the invoice.
Banging or knocking is most often trapped air in the radiators or piping, mineral buildup restricting flow, or pipes that were pitched incorrectly when the system was installed. It's diagnosable during a standard repair visit and usually doesn't require a full system replacement.
A boiler with no heat is usually one of a few things: a failed or sticking pilot/ignition component, low water tripping the safety cutoff on a steam system, a seized or miswired circulator pump on a hot-water system, or a thermostat/control issue rather than the boiler itself. We start every no-heat call by identifying which of these it actually is before recommending a repair.
Call right away if you have no heat during cold weather, smell gas near the unit, your carbon monoxide detector has alarmed, or you see water pooling at the base of the boiler — these aren't wait-and-see situations. Banging noises, uneven heat between rooms, or a pilot that won't stay lit are worth scheduling a visit for soon, even if the system is still limping along.
Yes. Loss of heat is treated as an emergency, and we dispatch technicians across Brooklyn and the rest of NYC nights, weekends, and holidays — a boiler failure in freezing weather doesn't wait for business hours, and neither do we.
We offer same-day appointments across NYC, including emergency no-heat calls, seven days a week.
Yes. Our partner technicians service both steam and hydronic hot-water boilers, common across every borough's housing stock.
It depends on the age and condition of the unit. During your visit we'll give you an honest comparison of repair cost versus a full boiler replacement rather than defaulting to one option.
For buildings with a boiler and radiators, yes — heating repair and boiler repair describe the same service. This page and our technicians cover both.
Yes, this is a large share of what we do across Brooklyn and Manhattan specifically. We're used to tight mechanical rooms, original piping, and coordinating with building management when needed.
Related Services
You May Also Need
From the Blog
More on Boiler Repair
How to Know if Your Boiler Needs Repair
The five warning signs NYC homeowners should never ignore before their boiler fails completely.
Boiler vs Water Heater: What's the Difference?
They're often confused, but a boiler and a water heater do very different jobs — and many NYC homes need both.
Steam vs Hot-Water Boilers: What NYC Homeowners Should Know
Two very different systems, both common across NYC — here's how to tell which one heats your home.
Need Boiler Repair?
Call now for same-day scheduling across New York City and Long Island.